(!)由於 Microsoft 2022 年 6 月 15 日終止支援,Internet Explorer 11 不屬於本網站之推薦環境。

  • 2024/12/28(六)~2025/1/5(日)適逢日本年假期間暫停出貨。 建議提早備貨以減少對交期的影響, 同時預防連假後出貨量遽增產生延遲。

異形線扁線彈簧 -SWF- 【金型用標準零件】 (SWF60-400)

扁線彈簧

異形線扁線彈簧 -SWF- 【金型用標準零件】 SWF60-400
  • 促銷至 2025/03/31截止

(i)請注意

  • 【FA機械用標準零件】的SWF系列為相同產品,刊載商品數可能不同,請依需求選用合適的規格。
  • 庫存促銷商品:本頁面部分商品是庫存促銷對象。
    促銷商品數量有限,視庫存狀況有可能提前結束或延長。促銷活動結束不另外通知,如有需求請盡早購買。

型號

商品篩選結果為1件時,會顯示商品型號。

SWF60-400

本頁所標註的為參考用的標準出貨日。確切的預定到貨日請以訂購完成通知書的資訊為準。

产品概述
SWF矩形螺旋弹簧产品概述
矩形螺旋弹簧是接受轴向压力的螺旋弹簧,通过压缩形变储能,从而提供缓冲回弹力。
台湾三住现有销售台湾三住自有品牌的SW*系列弹簧(品质优秀),X-SW*系列弹簧(更具性价比),可供客户选择。
产品特点
1. 广泛应用于模具制造加工行业,同时在其他行业也有所使用。
2. 台湾三住矩形螺旋弹簧使用油冷回火弹簧钢,提供稳定的负载,耐久的寿命。
3. 为了便于识别及防止生锈,台湾三住的矩形螺旋弹簧进行了喷漆。
4. 符合升级后的RoHS2.0 十项物质环保标准。ROHS图标
尺寸图
SWF矩形螺旋弹簧尺寸图
外径公差:D=6~60时,-0.7~0mm ; D=70时,-1.0~0mm
内径公差:d+0.1~+0.7mm
负载公差:±10%
垂直度:2°以下
自由长度公差: L<=50时,±0.5mm ; L>=55时,±1%
卷绕方向:右绕
规格概述
SWF矩形螺旋弹簧 规格概述
外径尺寸:Φ6~70mm

全长尺寸:10~500mm

压缩率及建议使用次数建议:
高压缩量 50%,建议使用次数30万次;
中压缩量 45%,建议使用次数50万次;
低压缩量 40%,建议使用次数100万次;
使用方法
1.弹簧使用时需要配套使用导向,在没有弹簧导向的条件下使用时,弹簧会发生纵弯曲和横弯曲等,弯曲的内侧会产生局部的高应力,
   使用导销,外径导承等弹簧导承。*一般来说,通过内径侧导承将导销自上而下贯通后使用最为理想。
2.有关弹簧的内径与导销
   建议导销杆径设定为比弹簧内径小1.0mm左右。如果与导销之间的间隙较小,导销就会使弹簧内径产生磨损,并以磨损部为起点,
   导致最终折损。另外,如果弹簧内径与导销之间的间隙过大,则会导致纵弯曲。(正确方式如图-1)
3.有关弹簧的外径与沉头孔
   建议沉头孔径设定比弹簧外径大1.5mm左右。如果与沉头孔之间的间隙较小时,会因弹簧压缩后外径侧膨胀,而导致弹簧外径与
   沉头孔摩擦造成截面变形,应力集中而导致最终折损。(正确方式如图-1)
4.务必保证在最大压缩量范围内使用弹簧,不能超行程使用。(如图-2)
5.弹簧使用预压后方可使用。
6.弹簧使用环境注意清洁,避免异物,废料的混入,夹杂。(如图-3)
7.注意确认弹簧安装面的平行度,安装面平行度较差,会导致弹簧的横弯曲,弯曲的内侧应力局部高应力,导致最终折损。(如图-4)
8.弹簧串联,内外相套,横向使用,均会导致弹簧耐久性降低以及折损。(如图-567)
SWF矩形螺旋弹簧 使用方法
使用案例
冲孔模用矩形螺旋弹簧 U型弯曲模用矩形螺旋弹簧
矩形螺旋弹簧通常可用于冲孔模,弯曲模等模具上,作缓冲回弹作用。
相关产品

3D預覽型號 

尚未指定完整型號,因此無法執行CAD檔案下載及3D預覽

  • ※ 欲執行CAD檔案下載及3D預覽時,需指定完整型號。
  • 請於左側「篩選規格・尺寸」確認完整型號,然後執行CAD檔案下載及3D預覽。
Loading...
型號
SWF60-400
型號數量折扣標準
出貨日
RoHS最大荷重
(N)
外徑(D)
(mm)
全長(L)
(mm)
涂装剥离处理
4天~ 10282060400有涂装

Loading...

  1. 1
规格表
DdL弹簧常数
N/mm{kgf/mm}
压紧长度
ℓmin
F=L×40%F=L×45%F=L×50%型式
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Type D-L
63157.8{0.80}7.16.047
{4.8}
6.853
{5.4}
7.559
{6.0}
SWF6-15
205.9{0.60}9.58.09.010.020
254.7{0.48}11.910.011.312.525
303.9{0.40}14.212.013.515.030
353.4{0.34}16.614.015.817.535
402.9{0.30}19.016.018.020.040
841015.7{1.60}4.54.063
{6.4}
4.571
{7.2}
5.079
{8.0}
SWF8-10
1510.5{1.07}6.86.06.87.515
207.8{0.80}9.08.09.010.020
256.3{0.64}11.310.011.212.525
305.2{0.53}13.512.013.515.030
354.5{0.46}15.814.015.717.535
403.9{0.40}18.016.018.020.040
453.5{0.36}20.318.020.222.545
503.1{0.32}22.520.022.525.050
552.9{0.29}24.822.024.727.555
602.6{0.27}27.024.027.030.060
652.4{0.25}30.826.029.332.565
702.2{0.23}33.228.031.535.070
752.1{0.21}35.630.033.837.575
802.0{0.20}37.932.036.040.080
1051019.6{2.00}4.54.078
{8.0}
4.588
{9.0}
5.098
{10}
SWF10-10
1513.1{1.33}6.86.06.87.515
209.8{1.00}9.08.09.010.020
257.8{0.80}11.310.011.212.525
306.5{0.67}13.512.013.515.030
355.9{0.57}15.814.015.717.535
404.9{0.50}18.016.018.020.040
454.4{0.44}20.318.020.222.545
503.9{0.40}22.520.022.525.050
553.6{0.36}24.822.024.727.555
603.3{0.33}27.024.027.030.060
653.0{0.31}29.326.029.232.565
702.8{0.29}31.528.031.535.070
752.6{0.27}33.830.033.737.575
802.5{0.25}36.032.036.040.080
902.2{0.22}40.536.040.545.090
1261518.3{1.87}6.86.0110
{11}
6.8124
{13}
7.5137
{14}
SWF12-15
2013.7{1.40}9.08.09.010.020
2511.0{1.12}11.310.011.212.525
309.2{0.93}13.512.013.515.030
357.8{0.80}15.814.015.717.535
406.9{0.70}18.016.018.020.040
456.1{0.62}20.318.020.222.545
505.5{0.56}22.520.022.525.050
555.0{0.51}24.822.024.727.555
604.6{0.47}27.024.027.030.060
654.2{0.43}29.326.029.232.565
703.9{0.40}31.528.031.535.070
753.7{0.37}33.830.033.737.575
803.4{0.35}36.032.036.040.080
903.1{0.31}40.536.040.545.090
1472017.7{1.80}9.08.0141
{14}
9.0159
{16}
10.0177
{18}
SWF14-20
2514.1{1.44}11.310.011.212.525
3011.8{1.20}13.512.013.515.030
3510.1{1.03}15.814.015.717.535
408.8{0.90}18.016.018.020.040
457.8{0.80}20.318.020.222.545
507.1{0.72}22.520.022.525.050
556.4{0.65}24.822.024.727.555
605.9{0.60}27.024.027.030.060
655.4{0.55}29.326.029.232.565
705.0{0.51}31.528.031.535.070
754.7{0.48}33.830.033.737.575
804.4{0.45}36.032.036.040.080
903.9{0.40}40.536.040.545.090
1003.5{0.36}45.040.045.050.0100
使用次数100万次50万次30万次 
 
DdL弹簧常数
N/mm{kgf/mm}
压紧长度
ℓmin
F=L×40%F=L×45%F=L×50%型式
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Type D-L
1682020.6{2.10}9.08.0165
{17}
9.0185
{19}
10.0206
{21}
SWF16-20
2516.5{1.68}11.310.011.212.525
3013.7{1.40}13.512.013.515.030
3511.8{1.20}15.814.015.717.535
4010.3{1.05}18.016.018.020.040
459.2{0.93}20.318.020.222.545
508.2{0.84}22.520.022.525.050
557.5{0.76}24.822.024.727.555
606.9{0.70}27.024.027.030.060
656.3{0.65}29.326.029.232.565
705.9{0.60}31.528.031.535.070
755.5{0.56}33.830.033.737.575
805.1{0.53}36.032.036.040.080
904.6{0.47}40.536.040.545.090
1004.1{0.42}45.040.045.050.0100
1253.3{0.34}56.350.056.362.5125
1892025.5{2.60}9.08.0204
{21}
9.0229
{23}
10.0255
{26}
SWF18-20
2520.4{2.08}11.310.011.212.525
3017.0{1.73}13.512.013.515.030
3514.6{1.49}15.814.015.717.535
4012.7{1.30}18.016.018.020.040
4511.3{1.16}20.318.020.222.545
5010.2{1.04}22.520.022.525.050
559.3{0.95}24.822.024.727.555
608.5{0.87}27.024.027.030.060
657.8{0.80}29.326.029.232.565
707.3{0.74}31.528.031.535.070
756.8{0.69}33.830.033.737.575
806.4{0.65}36.032.036.040.080
905.7{0.58}40.536.040.545.090
1005.1{0.52}45.040.045.050.0100
1254.1{0.42}56.350.056.362.5125
20112031.4{3.20}9.08.0251
{26}
9.0282
{29}
10.0314
{32}
SWF20-20
2525.1{2.56}11.310.011.212.525
3020.9{2.13}13.512.013.515.030
3517.9{1.83}15.814.015.717.535
4015.7{1.60}18.016.018.020.040
4513.9{1.42}20.318.020.222.545
5012.6{1.28}22.520.022.525.050
5511.4{1.16}24.822.024.727.555
6010.5{1.07}27.024.027.030.060
659.7{0.98}29.326.029.232.565
709.0{0.91}31.528.031.535.070
758.4{0.85}33.830.033.737.575
807.8{0.80}36.032.036.040.080
907.0{0.71}40.536.040.545.090
1006.3{0.64}45.040.045.050.0100
1255.0{0.51}56.350.056.262.5125
1504.2{0.43}67.560.067.575.0150
22112531.4{3.20}11.310.0314
{32}
11.2353
{36}
12.5392
{40}
SWF22-25
3026.2{2.67}13.512.013.515.030
3522.4{2.29}15.814.015.717.535
4019.6{2.00}18.016.018.020.040
4517.4{1.78}20.318.020.222.545
5015.7{1.60}22.520.022.525.050
5514.3{1.45}24.822.024.727.555
6013.1{1.33}27.024.027.030.060
6512.1{1.23}29.326.029.232.565
7011.2{1.14}31.528.031.535.070
7510.5{1.07}33.830.033.737.575
809.8{1.00}36.032.036.040.080
908.7{0.89}40.536.040.545.090
1007.8{0.80}45.040.045.050.0100
1256.3{0.64}56.350.056.262.5125
1505.2{0.53}67.560.067.575.0150
使用次数100万次50万次30万次  
 
DdL弹簧常数
N/mm{kgf/mm}
压紧长度
ℓmin
F=L×40%F=L×45%F=L×50%型式
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Type D-L
2513.52539.2{4.00}11.310.0392
{40}
11.2441
{45}
12.5490
{50}
SWF25-25
3032.7{3.33}13.512.013.515.030
3528.0{2.86}15.814.015.717.535
4024.5{2.50}18.016.018.020.040
4521.8{2.22}20.318.020.222.545
5019.6{2.00}22.520.022.525.050
5517.8{1.82}24.822.024.727.555
6016.3{1.67}27.024.027.030.060
6515.1{1.54}29.326.029.232.565
7014.0{1.43}31.528.031.535.070
7513.1{1.33}33.830.033.737.575
8012.3{1.25}36.032.036.040.080
9010.9{1.11}40.536.040.545.090
1009.8{1.00}45.040.045.050.0100
1257.8{0.80}56.350.056.262.5125
1506.5{0.67}67.560.067.575.0150
1755.6{0.57}78.870.078.787.5175
2004.9{0.50}90.080.090.0100.0200
2713.52547.1{4.80}11.310.0471
{48}
11.2530
{54}
12.5588
{60}
SWF27-25
3039.2{4.00}13.512.013.515.030
3533.6{3.43}15.814.015.717.535
4029.4{3.00}18.016.018.020.040
4526.2{2.67}20.318.020.222.545
5023.5{2.40}22.520.022.525.050
5521.4{2.18}24.822.024.727.555
6019.6{2.00}27.024.027.030.060
6518.1{1.85}29.326.029.232.565
7016.8{1.71}31.528.031.535.070
7515.7{1.60}33.830.033.737.575
8014.7{1.50}36.032.036.040.080
9013.1{1.33}40.536.040.545.090
10011.8{1.20}45.040.045.050.0100
1259.4{0.96}56.350.056.262.5125
1507.8{0.80}67.560.067.575.0150
1756.7{0.69}78.870.078.787.5175
2005.9{0.60}90.080.090.0100.0200
30162556.5{5.76}11.310.0565
{58}
11.2635
{65}
12.5706
{72}
SWF30-25
3047.1{4.80}13.512.013.515.030
3540.3{4.11}15.814.015.717.535
4035.3{3.60}18.016.018.020.040
4531.4{3.20}20.318.020.222.545
5028.2{2.88}22.520.022.525.050
5525.7{2.62}24.822.024.727.555
6023.5{2.40}27.024.027.030.060
6521.7{2.22}29.326.029.232.565
7020.2{2.06}31.528.031.535.070
7518.8{1.92}33.830.033.737.575
8017.7{1.80}36.032.036.040.080
9015.7{1.60}40.536.040.545.090
10014.1{1.44}45.040.045.050.0100
12511.3{1.15}56.350.056.262.5125
1509.4{0.96}67.560.067.575.0150
1758.1{0.82}78.870.078.787.5175
2007.1{0.72}90.080.090.0100.0200
35194048.0{4.89}18.016.0768
{78}
18.0864
{88}
20.0960
{98}
SWF35-40
4542.7{4.35}20.318.020.222.545
5038.4{3.92}22.520.022.525.050
5534.9{3.56}24.822.024.727.555
6032.0{3.26}27.024.027.030.060
6529.5{3.01}29.326.029.232.565
7027.4{2.80}31.528.031.535.070
7525.6{2.61}33.830.033.737.575
8024.0{2.45}36.032.036.040.080
9021.3{2.18}40.536.040.545.090
10019.2{1.96}45.040.045.050.0100
12515.4{1.57}56.350.056.262.5125
15012.8{1.31}67.560.067.575.0150
17511.0{1.12}78.870.078.787.5175
2009.6{0.98}90.080.090.0100.0200
使用次数100万次50万次30万次  
 
DdL弹簧常数
N/mm{kgf/mm}
压紧长度
ℓmin
F=L×40%F=L×45%F=L×50%型式
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Fmm负载
N{kgf}
Type D-L
40224062.7{6.39}18.016.01003
{102}
18.01129
{115}
20.01254
{128}
SWF40-40
4555.7{5.68}21.318.020.322.545
5050.2{5.11}22.520.022.525.050
5545.6{4.65}26.122.024.827.555
6041.8{4.26}27.024.027.030.060
6538.6{3.93}30.826.029.332.565
7035.8{3.65}31.528.031.535.070
7533.4{3.41}35.630.033.837.575
8031.4{3.20}36.032.036.040.080
9027.9{2.84}40.536.040.545.090
10025.1{2.56}45.040.045.050.0100
12520.1{2.05}56.350.056.262.5125
15016.7{1.70}67.560.067.575.0150
17514.3{1.46}78.870.078.787.5175
20012.5{1.28}90.080.090.0100.0200
22511.1{1.14}101.090.0101.3112.5225
25010.0{1.02}112.5100.0112.5125.0250
2759.1{0.93}124.0110.0123.8137.5275
3008.4{0.85}142.2120.0135.0150.0300
5027.55078.4{7.99}22.520.01568
{160}
22.51764
{180}
25.01960
{200}
SWF50-50
5571.3{7.27}24.822.024.827.555
6065.3{6.66}27.024.027.030.060
6560.3{6.15}29.326.029.332.565
7056.0{5.71}31.528.031.535.070
7552.3{5.33}33.830.033.837.575
8049.0{5.00}36.032.036.040.080
9043.6{4.44}40.536.040.545.090
10039.2{4.00}45.040.045.050.0100
12531.4{3.20}56.350.056.262.5125
15026.1{2.66}67.560.067.575.0150
17522.4{2.28}78.870.078.787.5175
20019.6{2.00}90.080.090.0100.0200
22517.4{1.78}101.090.0101.3112.5225
25015.7{1.60}112.5100.0112.5125.0250
27514.3{1.45}124.0110.0123.8137.5275
30013.1{1.33}135.0120.0135.0150.0300
35011.2{1.14}165.9140.0157.5175.0350
4009.8{1.00}189.6160.0180.0200.0400
4508.7{0.89}213.3180.0202.5225.0450
5007.8{0.80}237.0200.0225.0250.0500
60336094.0{9.59}27.024.02256
{230}
27.02538
{259}
30.02820
{288}
SWF60-60
7080.6{8.22}31.528.031.535.070
8070.5{7.19}36.032.036.040.080
9062.7{6.39}40.536.040.045.090
10056.4{5.75}45.040.045.050.0100
12545.1{4.60}56.350.056.262.5125
15037.6{3.83}67.560.067.575.0150
17532.2{3.29}78.870.078.787.5175
20028.2{2.88}90.080.090.0100.0200
22525.1{2.56}101.390.0101.3112.5225
25022.6{2.30}112.5100.0112.5125.0250
27520.5{2.09}123.8110.0123.8137.5275
30018.8{1.92}135.0120.0135.0150.0300
35016.1{1.64}165.9140.0157.5175.0350
40014.1{1.44}189.6160.0180.0200.0400
45012.5{1.28}213.3180.0202.5225.0450
50011.3{1.15}237.0200.0225.0250.0500
7038.570112{11.4}33.228.03136
{320}
31.53528
{360}
35.03920
{400}
SWF70-70
8098.0{9.99}37.932.036.040.080
9087.1{8.88}42.736.040.545.090
10078.4{7.99}47.440.045.050.0100
12562.7{6.40}59.350.056.362.5125
15052.3{5.33}71.160.067.575.0150
17544.8{4.57}83.070.078.887.5175
20039.2{4.00}94.880.090.0100.0200
25031.4{3.20}118.5100.0112.5125.0250
30026.1{2.66}142.2120.0135.0150.0300
35022.4{2.28}165.9140.0157.5175.0350
使用次数100万次50万次30万次  

概述・特性

矩形螺旋弹簧(模具弹簧) -SWF-:相关图像


 

基本資訊

容許壓縮率(%) 50 品牌 MISUMI

異形線扁線彈簧 -SWF- 【金型用標準零件】的型號SWF60-400頁面。
記載關於型號SWF60-400之規格、尺寸、型式情報。

本商品分類

型號
NT-SWF10-25
NT-SWF10-30
NT-SWF10-35
SWF60-450
SWF60-500
SWF60-60
型號數量折扣標準
出貨日
RoHS最大荷重
(N)
外徑(D)
(mm)
全長(L)
(mm)
涂装剥离处理
8天~ 10981025无涂装
8天~ 10981030无涂装
8天~ 10981035无涂装
當日可能 10282060450有涂装
當日可能 10282060500有涂装
當日可能 1028206060有涂装

此分類還有這些商品

看過此商品的人也看過這些商品

與此商品分類相關的三住i組裝案例

技術支援服務

沖壓模具零件
Tel:02-25703766 / FAX:02-25703767